Silver Shop
Maximum profit: 20%
Gold Shop
Maximum profit: 21%
Platinum Shop
Maximum profit: 22%
Top

Carbide end mill FAQ: selection, parameters, coatings, custom tools

Knowledge Center Nov 19, 2026

Material selection: which cutter for which workpiece

What is the best end mill for aluminum?

For aluminum, a 3-flute end mill with a high helix and polished flutes is the usual starting point. The polished surface stops soft aluminium from welding to the edge, which is the most common cause of poor finish. Uncoated or ZrN-coated tools usually beat AlTiN here because AlTiN contains aluminium and increases built-up edge. Run high spindle speed with strong chip evacuation, either flood coolant or MQL. For deep slots where chip room matters more than finish, drop to a single-flute cutter.

Which cutter should I use for graphite electrodes?

Graphite is abrasive rather than gummy, so the tool fails by wear, not by built-up edge. Use a diamond-coated (CVD) carbide tool with a low rake angle and a sharp, honed edge. Machine dry with high spindle speed and strong dust extraction; coolant turns graphite dust into a conductive slurry that damages machines and electronics. Expect tool life measured in electrodes rather than hours, and keep a wear log so you can replace tools before the edge rounds and starts burning the workpiece.

Can I mill carbon fiber with a standard end mill?

You can, but a standard end mill will delaminate the top and bottom plies and wear out quickly. CFRP needs a diamond-coated cutter with a compression or burr geometry so the cutting forces point inward on both faces. Use high spindle speed with low feed per tooth, clamp the laminate rigidly, and extract dust at the cut line. Edges that look fine often hide subsurface cracks, so inspect a scrap piece under magnification before committing a production batch.

What end mill should I use for titanium?

Titanium work-hardens and conducts heat poorly, so the heat goes into the edge. Use a sharp, uncoated or thin-coated carbide tool with a low helix, run low surface speed with a high feed per tooth, and never let the tool rub. Flood coolant is essentially mandatory, and it must be chlorine-free. Keep radial engagement moderate and climb mill. If you dwell or take tiny cuts, the surface hardens and the next pass destroys the edge.

Best cutter for hardened steel above 50 HRC?

Use a solid carbide end mill with an AlTiN or TiAlN coating and a high helix, run at low surface speed with a small radial depth of cut and a rigid, short-overhang setup. Hard milling removes the need for EDM in many mould cavities, but it leaves no margin for chatter: any vibration shows up as chipping on the cutting edge. Start conservative, verify with a single test cut, and increase feed before you increase speed.

Why does my cutter grab and squeal in copper and brass?

Soft, ductile metals grab when the edge rubs instead of cutting. The usual fixes are a higher rake angle, polished flutes, fewer flutes for more chip room, and enough feed per tooth to keep the edge biting. A worn or chipped edge will rub even with correct parameters, so check the edge under a magnifier first. In brass, avoid zero-rake tools that were designed for steel; they push material instead of shearing it.

How do I stop stainless steel from work hardening?

Keep the tool cutting, never dwelling. Climb milling, a sharp edge, a feed per tooth high enough to stay under the hardened layer, and copious coolant all matter. If a previous operation already hardened the surface, take a deeper pass that gets under the hard skin rather than a light spring pass that skates on it. Stainless also responds badly to re-cutting chips, so chip evacuation is part of the cutting strategy, not an afterthought.

Troubleshooting: why tools fail

Why do my end mills break at the shank?

Breakage at the shank is almost never a cutting-edge problem. It points to bending load: excessive overhang, poor runout, an unbalanced holder, or a tool pulled out of the collet. Check runout with a dial indicator at the cutting edge, shorten the overhang where possible, and confirm the collet is clean and within torque. If the break face shows a fatigue pattern, the tool has been vibrating for a while before it let go.

Why is my cut chattering?

Chatter comes from insufficient rigidity somewhere in the loop: tool, holder, fixture, or machine. Shorten the overhang, use a heavier holder, and reduce radial depth while raising feed per tooth, which moves the process out of the unstable zone. A variable-helix tool breaks up the resonance and often helps more than slowing down. If the workpiece is thin, support it from behind; clamping is frequently the real bottleneck.

Why is the surface finish rough on aluminium?

Rough finish on aluminium is usually built-up edge: soft metal welding to the edge and then breaking away. Check for a dull or polished-away edge, switch to a sharper high-helix tool with polished flutes, increase spindle speed, and improve chip evacuation. Insufficient coolant flow can be worse than none, because it creates thermal cycling without clearing chips. Confirm the tool is not rubbing by looking for a bright band on the flank.

Why do corners chip when machining graphite?

Graphite is brittle and abrasive, so the cutting edge fails mechanically. Chipping at corners usually means the tool is exiting the cut too fast or the edge geometry is too sharp for the grade. Use a diamond-coated tool with a honed edge, reduce feed at the exit, and consider a smaller stepover. Keep an electrode count per tool and replace on schedule rather than on failure, since a chipped edge silently burns the next part.

Why does thread milling produce a tapered or oversized thread?

A tapered thread usually means tool runout or a compensation error rather than a worn cutter. Check the tool for runout in the holder, verify the thread pitch and the helical interpolation parameters, and confirm cutter compensation is applied in the direction of the cut. With a single-profile tool, the path must be exact; with a multi-tooth tool, a small pitch error accumulates over the thread length. Measure with a thread gauge or three-wire method before adjusting anything.

Why is my tool wearing only on the flank?

Flank wear concentrated on one area is normal abrasive wear, but rapid flank wear points to surface speed that is too high for the material, or a coating that does not match it. Aluminium and graphite are abrasive and punish uncoated edges; hardened steel punishes tools without a hard coating. Reduce speed before reducing feed, and log wear against cutting length so replacement becomes predictable instead of reactive.

Cutting parameters

What spindle speed should I use for a 6 mm carbide end mill in aluminium?

Work from surface speed, not from a fixed rpm. For aluminium, a starting range of 300 to 500 m/min surface speed puts a 6 mm tool at roughly 16,000 to 26,000 rpm. Most machines cannot reach that, which is fine: run at the machine maximum with adequate chip load and let the feed per tooth do the work. Verify on a test cut and watch for built-up edge and chip welding, which tell you the speed is too low or the coolant is inadequate.

How many flutes should an aluminium cutter have?

One flute for deep pockets and roughing where chip evacuation limits you, three flutes for a balance of finish and productivity, and two flutes for general work. More flutes means less chip room, and aluminium chips are bulky, so a 4-flute tool in a deep slot will clog even with good coolant. For finishing walls and floors where the chip load is small, three flutes is usually the sweet spot.

How many flutes for steel?

Four flutes is the default for general steel milling, five or six for finishing passes where chip room is not the constraint. Fewer flutes give more chip room and better performance in soft, gummy steels; more flutes give a stronger core and better finish at lower feed per tooth. In stainless, avoid very high flute counts unless your chip evacuation is genuinely good.

What feed per tooth should I start with?

For a 6 mm carbide tool in aluminium, 0.02 to 0.05 mm per tooth is a reasonable starting window. In steel, start around 0.02 to 0.04 mm per tooth and adjust from the chip: thin, powdery chips mean you are rubbing, thick blue chips mean you are overloading. Feed per tooth matters more than table feed, because it controls whether the edge cuts or rubs. Always verify on scrap before running a production batch.

What depth of cut should I take?

Two stable strategies exist: light radial engagement with a large axial depth (high-efficiency milling), or the reverse. For aluminium, a radial depth of 5 to 10 percent of diameter with an axial depth of one to two diameters is efficient on a rigid machine. On a lighter machine, reduce axial depth first and keep the feed per tooth up, because starving the feed is what destroys edges.

Do I need coolant when milling aluminium?

You need chip evacuation more than you need cooling. Flood coolant, MQL, or high-pressure air can all work, but a weak dribble of coolant is the worst option: it creates thermal cycling without clearing chips. For deep pockets, air blast plus a polished flute often outperforms flood. For finishing cuts where surface finish matters, flood is easier to control.

Can I machine graphite dry?

Yes, and you generally should. Graphite is machined dry with dust extraction; coolant turns the dust into a conductive slurry that migrates into ways, bearings, and electronics, and it is far harder to remove than dry dust. Use a sealed machine or a dedicated graphite cell, extract at the cut line, and treat the dust as a health hazard requiring proper filtration.

Coatings

AlTiN, TiAlN, or DLC: which coating when?

AlTiN and TiAlN are hard, heat-resistant coatings for steel, stainless, and hardened materials where the edge runs hot. DLC is a low-friction coating for aluminium, copper, and other non-ferrous metals where the enemy is built-up edge rather than heat. Diamond coating is for graphite, CFRP, and other highly abrasive non-metals. Choosing a steel coating for aluminium is one of the most common and most expensive mistakes.

Does coating help when cutting aluminium?

Often it does not. Many aluminium operations run best with an uncoated, polished tool, because the polished surface is what prevents welding. If you need a coating, DLC or a dedicated non-ferrous coating reduces friction without adding aluminium to the surface chemistry. Avoid AlTiN: it contains aluminium and encourages the exact built-up edge you are trying to prevent.

Tool geometry

Ball nose or bull nose for 3D finishing?

Ball nose gives a constant radius and predictable scallop height, which makes it the standard for 3D surfaces. A bull nose (corner radius) tool removes material faster and leaves a flatter floor, but its scallop profile changes with stepover. Use ball nose for steep, curved geometry and bull nose for floors and shallow slopes. Reducing stepover is usually cheaper than switching geometry when finish is the problem.

Single flute or three flute for aluminium?

Single flute maximises chip room, which matters in deep pockets, plastics, and high-rpm spindles on light machines. Three flute gives better finish, higher feed rates, and a stronger core, which matters for wall finishing and production work. If you are fighting chip evacuation, go single flute; if you are fighting finish or cycle time, go three flute.

What is a variable helix tool for?

A variable helix changes the flute pitch along the tool so that each flute hits the workpiece at a different moment. That breaks the regular excitation that causes chatter, and it is why variable-helix tools often outperform constant-helix tools in unstable setups. They are not a substitute for rigidity, but they buy margin when the machine or fixture is the weak link.

How much should I reduce parameters for long reach tools?

Long reach tools deflect, so reduce radial engagement before you reduce feed per tooth. A rule of thumb is to cut radial depth roughly in proportion to the stiffness loss, which falls with the cube of the overhang. In practice, take a spring pass, listen for chatter, and inspect the wall for taper. If the wall is tapered, the tool is pushing away and you need either less engagement or a shorter tool.

Ordering, custom tools, and samples

What is the minimum order quantity?

Standard catalogue sizes ship from one piece, so a job shop can buy a single cutter to finish an urgent job. Custom non-standard geometry usually starts at a small batch because of setup and grinding time, and the exact minimum depends on the diameter, tolerance, and coating. Ask for a quote with your drawing and quantity and you will get the minimum stated explicitly rather than as a range.

How long does a custom tool take?

Typical lead time for a custom carbide cutter is a few working days for simple geometry and longer for multi-step tools, tight tolerances, or special coatings. If the job is urgent, say so up front: sample-sized quantities can often be prioritised. Confirm the lead time in writing on the quotation, because a verbal estimate is not something you can plan production around.

Do you supply samples for trial cutting?

Yes. Trial cutting is the only honest way to prove a tool in your own machine, material, and fixture, so samples are available before a volume order. Send the workpiece material, the operation, and your existing parameters, and you will get a tool matched to that case rather than a generic recommendation. Record the result: cut count, edge condition, and surface finish become the reference for the production order.

What do you need to quote a non-standard tool?

A drawing in DXF, PDF, or STEP, plus the workpiece material, the machine, the operation, the tolerance, and the quantity. If a drawing is not available, a dimensioned sketch with the critical angles and radii is enough to start. Missing information is the usual reason a quote takes days instead of hours, so list what you know and flag what you are unsure about.